Six Sigma (6?) is a set of techniques and tools for process improvement. It was introduced by American engineer Bill Smith while working at Motorola in 1980.Jack Welch made it central to his business strategy at General Electric in 1995. A six sigma process is one in which 99.99966% of all opportunities to produce some feature of a part are statistically expected to be free of defects.
Six Sigma strategies seek to improve the quality of the output of a process by identifying and removing the causes of defects and minimizing impact variability in manufacturing and business processes. It uses a set of quality management methods, mainly empirical, statistical methods, and creates a special infrastructure of people within the organization who are experts in these methods. Each Six Sigma project carried out within an organization follows a defined sequence of steps and has specific value targets, for example: reduce process cycle time, reduce pollution, reduce costs, increase customer satisfaction, and increase profits.
The term Six Sigma (capitalized because it was written that way when registered as a Motorola trademark on December 28, 1993) originated from terminology associated with statistical modeling of manufacturing processes. The maturity of a manufacturing process can be described by a sigma rating indicating its yield or the percentage of defect-free products it creates--specifically, within how many standard deviations of a normal distribution the fraction of defect-free outcomes corresponds to. Motorola set a goal of "six sigma" for all of its manufacturing.
Six Sigma doctrine asserts:
Features that set Six Sigma apart from previous quality-improvement initiatives include:
The term "six sigma" comes from statistics and is used in statistical quality control, which evaluates process capability. Originally, it referred to the ability of manufacturing processes to produce a very high proportion of output within specification. Processes that operate with "six sigma quality" over the short term are assumed to produce long-term defect levels below 3.4 defects per million opportunities (DPMO). The 3.4 dpmo is based on a "shift" of ± 1.5 sigma explained by Dr. Mikel J. Harry. This figure is based on the tolerance in the height of a stack of discs. Six Sigma's implicit goal is to improve all processes, but not to the 3.4 DPMO level necessarily. Organizations need to determine an appropriate sigma level for each of their most important processes and strive to achieve these. As a result of this goal, it is incumbent on management of the organization to prioritize areas of improvement.
"Six Sigma" was registered June 11, 1991 as . In 2005 Motorola attributed over US$17 billion in savings to Six Sigma.
Other early adopters of Six Sigma include Honeywell and General Electric, where Jack Welch introduced the method. By the late 1990s, about two-thirds of the Fortune 500 organizations had begun Six Sigma initiatives with the aim of reducing costs and improving quality.
In recent yearslean manufacturing to create a methodology named Lean Six Sigma. The Lean Six Sigma methodology views lean manufacturing, which addresses process flow and waste issues, and Six Sigma, with its focus on variation and design, as complementary disciplines aimed at promoting "business and operational excellence"., some practitioners have combined Six Sigma ideas with
In 2011, the International Organization for Standardization (ISO) has published the first standard "ISO 13053:2011" defining a Six Sigma process. Other standards have been created mostly by universities or companies that have first-party certification programs for Six Sigma.
Lean management and Six Sigma are two concepts which share similar methodologies and tools. Both programs are Japanese-influenced, but they are two different programs. Lean management is focused on eliminating waste using a set of proven standardized tools and methodologies that target organizational efficiencies while integrating a performance improvement system utilized by everyone, while Six Sigma's focus is on eliminating defects and reducing variation. Both systems are driven by data, though Six Sigma is much more dependent on accurate data.
The DMAIC project methodology has five phases:
Some organizations add a Recognize step at the beginning, which is to recognize the right problem to work on, thus yielding an RDMAIC methodology.
The DMADV project methodology, known as DFSS ("Design For Six Sigma"), features five phases:
Within the individual phases of a DMAIC or DMADV project, Six Sigma utilizes many established quality-management tools that are also used outside Six Sigma. The following table shows an overview of the main methods used.
One key innovation of Six Sigma involves the absolute "professionalizing" of quality management functions. Prior to Six Sigma, quality management in practice was largely relegated to the production floor and to statisticians in a separate quality department. Formal Six Sigma programs adopt a kind of elite ranking terminology (similar to some martial arts systems, like judo) to define a hierarchy (and special career path) that includes all business functions and levels.
Six Sigma identifies several key roles for its successful implementation.
According to proponents of the system, special training is needed for all of these practitioners to ensure that they follow the methodology and use the data-driven approach correctly.
Some organizations use additional belt colours, such as Yellow Belts, for employees that have basic training in Six Sigma tools and generally participate in projects and "White belts" for those locally trained in the concepts but do not participate in the project team. "Orange belts" are also mentioned to be used for special cases.
General Electric and Motorola developed certification programs as part of their Six Sigma implementation, verifying individuals' command of the Six Sigma methods at the relevant skill level (Green Belt, Black Belt etc.). Following this approach, many organizations in the 1990s started offering Six Sigma certifications to their employees. In 2008 Motorola University later co-developed with Vative and the Lean Six Sigma Society of Professionals a set of comparable certification standards for Lean Certification. Criteria for Green Belt and Black Belt certification vary; some companies simply require participation in a course and a Six Sigma project. There is no standard certification body, and different certification services are offered by various quality associations and other providers against a fee.[self-published source] The American Society for Quality for example requires Black Belt applicants to pass a written exam and to provide a signed affidavit stating that they have completed two projects or one project combined with three years' practical experience in the body of knowledge.
The term "six sigma process" comes from the notion that if one has six standard deviations between the process mean and the nearest specification limit, as shown in the graph, practically no[failed verification] items will fail to meet specifications. This is based on the calculation method employed in process capability studies.
Capability studies measure the number of standard deviations between the process mean and the nearest specification limit in sigma units, represented by the Greek letter ? (sigma). As process standard deviation goes up, or the mean of the process moves away from the center of the tolerance, fewer standard deviations will fit between the mean and the nearest specification limit, decreasing the sigma number and increasing the likelihood of items outside specification. One should also note that calculation of Sigma levels for a process data is independent of the data being normally distributed. In one of the criticisms to Six Sigma, practitioners using this approach spend a lot of time transforming data from non-normal to normal using transformation techniques. It must be said that Sigma levels can be determined for process data that has evidence of non-normality.
Experience has shown that processes usually do not perform as well in the long term as they do in the short term. As a result, the number of sigmas that will fit between the process mean and the nearest specification limit may well drop over time, compared to an initial short-term study. To account for this real-life increase in process variation over time, an empirically based 1.5 sigma shift is introduced into the calculation. According to this idea, a process that fits 6 sigma between the process mean and the nearest specification limit in a short-term study will in the long term fit only 4.5 sigma - either because the process mean will move over time, or because the long-term standard deviation of the process will be greater than that observed in the short term, or both.
Hence the widely accepted definition of a six sigma process is a process that produces 3.4 defective parts per million opportunities (DPMO). This is based on the fact that a process that is normally distributed will have 3.4 parts per million outside the limits, when the limits are six sigma from the "original" mean of zero and the process mean is then shifted by 1.5 sigma (and therefore, the six sigma limits are no longer symmetrical about the mean). The former six sigma distribution, when under the effect of the 1.5 sigma shift, is commonly referred to as a 4.5 sigma process. The failure rate of a six sigma distribution with the mean shifted 1.5 sigma is not equivalent to the failure rate of a 4.5 sigma process with the mean centered on zero. This allows for the fact that special causes may result in a deterioration in process performance over time and is designed to prevent underestimation of the defect levels likely to be encountered in real-life operation.
The role of the sigma shift is mainly academic. The purpose of six sigma is to generate organizational performance improvement. It is up to the organization to determine, based on customer expectations, what the appropriate sigma level of a process is. The purpose of the sigma value is as a comparative figure to determine whether a process is improving, deteriorating, stagnant or non-competitive with others in the same business. Six sigma (3.4 DPMO) is not the goal of all processes.
These figures assume that the process mean will shift by 1.5 sigma toward the side with the critical specification limit. In other words, they assume that after the initial study determining the short-term sigma level, the long-term Cpk value will turn out to be 0.5 less than the short-term Cpk value. So, now for example, the DPMO figure given for 1 sigma assumes that the long-term process mean will be 0.5 sigma beyond the specification limit (Cpk = -0.17), rather than 1 sigma within it, as it was in the short-term study (Cpk = 0.33). Note that the defect percentages indicate only defects exceeding the specification limit to which the process mean is nearest. Defects beyond the far specification limit are not included in the percentages.
The formula used here to calculate the DPMO is thus
|Sigma level||Sigma (with 1.5? shift)||DPMO||Percent defective||Percentage yield||Short-term Cpk||Long-term Cpk|
Six Sigma mostly finds application in large organizations. An important factor in the spread of Six Sigma was GE's 1998 announcement of $350 million in savings thanks to Six Sigma, a figure that later grew to more than $1 billion. According to industry consultants like Thomas Pyzdek and John Kullmann, companies with fewer than 500 employees are less suited to Six Sigma implementation or need to adapt the standard approach to make it work for them. Six Sigma however contains a large number of tools and techniques that work well in small to mid-size organizations. The fact that an organization is not big enough to be able to afford black belts does not diminish its abilities to make improvements using this set of tools and techniques. The infrastructure described as necessary to support Six Sigma is a result of the size of the organization rather than a requirement of Six Sigma itself.
Although the scope of Six Sigma differs depending on where it is implemented, it can successfully deliver its benefits to different applications.
After its first application at Motorola in the late 1980s, other internationally recognized firms currently recorded high number of savings after applying Six Sigma. Examples of these are Johnson and Johnson, with $600 million of reported savings, Texas Instruments, which saved over $500 million as well as Telefónica de Espana, which reported EUR30 million in savings in the first 10 months. On top of this, other organizations like Sony and Boeing achieved large percentages in waste reduction.
Although companies have considered common quality control and process improvement strategies, there's still a need for more reasonable and effective methods as all the desired standards and client satisfaction have not always been reached. There is still a need for an essential analysis that can control the factors affecting concrete cracks and slippage between concrete and steel. After conducting a case study on Tinjin Xianyi Construction Technology Co, Ltd., it was found that construction time and construction waste were reduced by 26.2% and 67% accordingly after adopting Six Sigma. Similarly, Six Sigma implementation was studied at one of the largest engineering and construction companies in the world: Bechtel Corporation, where after an initial investment of $30 million in a Six Sigma program that included identifying and preventing rework and defects, over $200 million were saved.
Six Sigma has played an important role by improving accuracy of allocation of cash to reduce bank charges, automatic payments, improving accuracy of reporting, reducing documentary credits defects, reducing check collection defects, and reducing variation in collector performance. Two of the financial institutions that have reported considerable improvements in their operations are Bank of America and American Express. By 2004 Bank of America increased customer satisfaction by 10.4% and decreased customer issues by 24% by applying Six Sigma tools in their streamline operations. Similarly, American Express successfully eliminated non-received renewal credit cards and improved their overall processes by applying Six Sigma principles. This strategy is also currently being applied by other financial institutions like GE Capital Corp., JP Morgan Chase, and SunTrust Bank, with customer satisfaction being their main objective.
In this field, it is important to ensure that products are delivered to clients at the right time while preserving high-quality standards from the beginning to the end of the supply chain. By changing the schematic diagram for the supply chain, Six Sigma can ensure quality control on products (defect free) and guarantee delivery deadlines, which are the two major issues involved in the supply chain.
This is a sector that has been highly matched with this doctrine for many years because of the nature of zero tolerance for mistakes and potential for reducing medical errors involved in healthcare. The goal of Six Sigma in healthcare is broad and includes reducing the inventory of equipment that brings extra costs, altering the process of healthcare delivery in order to make more efficient and refining reimbursements. A study at the University of Texas MD Anderson Cancer Center, which recorded an increase in examinations with no additional machines of 45% and reduction in patients' preparation time of 40 minutes; from 45 minutes to 5 minutes in multiple cases.
Quality expert Joseph M. Juran described Six Sigma as "a basic version of quality improvement", stating that "there is nothing new there. It includes what we used to call facilitators. They've adopted more flamboyant terms, like belts with different colors. I think that concept has merit to set apart, to create specialists who can be very helpful. Again, that's not a new idea. The American Society for Quality long ago established certificates, such as for reliability engineers."
Quality expert Philip B. Crosby pointed out that the Six Sigma standard does not go far enough--customers deserve defect-free products every time. For example, under the Six Sigma standard, semiconductors which require the flawless etching of millions of tiny circuits onto a single chip are all defective.
The use of "Black Belts" as itinerant change agents has fostered an industry of training and certification. Critics have argued there is overselling of Six Sigma by too great a number of consulting firms, many of which claim expertise in Six Sigma when they have only a rudimentary understanding of the tools and techniques involved or the markets or industries in which they are acting.
A Fortune article stated that "of 58 large companies that have announced Six Sigma programs, 91 percent have trailed the S&P 500 since". The statement was attributed to "an analysis by Charles Holland of consulting firm Qualpro (which espouses a competing quality-improvement process)". The summary of the article is that Six Sigma is effective at what it is intended to do, but that it is "narrowly designed to fix an existing process" and does not help in "coming up with new products or disruptive technologies."
A more direct criticism is the "rigid" nature of Six Sigma with its over-reliance on methods and tools. In most cases, more attention is paid to reducing variation and searching for any significant factors and less attention is paid to developing robustness in the first place (which can altogether eliminate the need for reducing variation). The extensive reliance on significance testing and use of multiple regression techniques increases the risk of making commonly unknown types of statistical errors or mistakes. A possible consequence of Six Sigma's array of P-value misconceptions is the false belief that the probability of a conclusion being in error can be calculated from the data in a single experiment without reference to external evidence or the plausibility of the underlying mechanism. One of the most serious but all-too-common misuses of inferential statistics is to take a model that was developed through exploratory model building and subject it to the same sorts of statistical tests that are used to validate a model that was specified in advance.
Another comment refers to the often mentioned Transfer Function, which seems to be a flawed theory if looked at in detail. Since significance tests were first popularized many objections have been voiced by prominent and respected statisticians. The volume of criticism and rebuttal has filled books with language seldom used in the scholarly debate of a dry subject. Much of the first criticism was already published more than 40 years ago (see Statistical hypothesis testing § Criticism).
Articles featuring critics have appeared in the November-December 2006 issue of USA Army Logistician regarding Six-Sigma: "The dangers of a single paradigmatic orientation (in this case, that of technical rationality) can blind us to values associated with double-loop learning and the learning organization, organization adaptability, workforce creativity and development, humanizing the workplace, cultural awareness, and strategy making."
Nassim Nicholas Taleb considers risk managers little more than "blind users" of statistical tools and methods. He states that statistics is fundamentally incomplete as a field as it cannot predict the risk of rare events--something Six Sigma is specially concerned with. Furthermore, errors in prediction are likely to occur as a result of ignorance for or distinction between epistemic and other uncertainties. These errors are the biggest in time variant (reliability) related failures.
According to an article by John Dodge, editor in chief of Design News, use of Six Sigma is inappropriate in a research environment. Dodge states "excessive metrics, steps, measurements and Six Sigma's intense focus on reducing variability water down the discovery process. Under Six Sigma, the free-wheeling nature of brainstorming and the serendipitous side of discovery is stifled." He concludes "there's general agreement that freedom in basic or pure research is preferable while Six Sigma works best in incremental innovation when there's an expressed commercial goal."
A BusinessWeek article says that James McNerney's introduction of Six Sigma at 3M had the effect of stifling creativity and reports its removal from the research function. It cites two Wharton School professors who say that Six Sigma leads to incremental innovation at the expense of blue skies research. This phenomenon is further explored in the book Going Lean, which describes a related approach known as lean dynamics and provides data to show that Ford's "6 Sigma" program did little to change its fortunes.
One criticism voiced by Yasar Jarrar and Andy Neely from the Cranfield School of Management's Centre for Business Performance is that while Six Sigma is a powerful approach, it can also unduly dominate an organization's culture; and they add that much of the Six Sigma literature - in a remarkable way (six-sigma claims to be evidence, scientifically based) - lacks academic rigor:
One final criticism, probably more to the Six Sigma literature than concepts, relates to the evidence for Six Sigma's success. So far, documented case studies using the Six Sigma methods are presented as the strongest evidence for its success. However, looking at these documented cases, and apart from a few that are detailed from the experience of leading organizations like GE and Motorola, most cases are not documented in a systemic or academic manner. In fact, the majority are case studies illustrated on websites, and are, at best, sketchy. They provide no mention of any specific Six Sigma methods that were used to resolve the problems. It has been argued that by relying on the Six Sigma criteria, management is lulled into the idea that something is being done about quality, whereas any resulting improvement is accidental (Latzko 1995). Thus, when looking at the evidence put forward for Six Sigma success, mostly by consultants and people with vested interests, the question that begs to be asked is: are we making a true improvement with Six Sigma methods or just getting skilled at telling stories? Everyone seems to believe that we are making true improvements, but there is some way to go to document these empirically and clarify the causal relations.-- 
The 1.5 sigma shift has also become contentious because it results in stated "sigma levels" that reflect short-term rather than long-term performance: a process that has long-term defect levels corresponding to 4.5 sigma performance is, by Six Sigma convention, described as a "six sigma process." The accepted Six Sigma scoring system thus cannot be equated to actual normal distribution probabilities for the stated number of standard deviations, and this has been a key bone of contention over how Six Sigma measures are defined. The fact that it is rarely explained that a "6 sigma" process will have long-term defect rates corresponding to 4.5 sigma performance rather than actual 6 sigma performance has led several commentators to express the opinion that Six Sigma is a confidence trick.
Quality is measured by the price of nonconformance, not by indexes.
The nonconformance situation semiconductor suppliers found recently emerged from embracing the standard of "Six Sigma." This permits 3.4 defects per million components. Why anyone would want to do that is beyond me. But they are now paying the price. When even ordinary chips contain a million or more components, such a standard means that they are all defective.