NACA Airfoil

Get NACA Airfoil essential facts below. View Videos or join the NACA Airfoil discussion. Add NACA Airfoil to your PopFlock.com topic list for future reference or share this resource on social media.
## Four-digit series

### Equation for a symmetrical 4-digit NACA airfoil

### Equation for a cambered 4-digit NACA airfoil

## Five-digit series

### Non-reflexed 3 digit camber lines

### Reflexed 3-digit camber lines

## Modifications

## 1-series

## 6-series

## 7-series

## 8-series

## See also

## References

## External links

This article uses material from the Wikipedia page available here. It is released under the Creative Commons Attribution-Share-Alike License 3.0.

NACA Airfoil

The **NACA airfoils** are airfoil shapes for aircraft wings developed by the National Advisory Committee for Aeronautics (NACA). The shape of the NACA airfoils is described using a series of digits following the word "NACA". The parameters in the numerical code can be entered into equations to precisely generate the cross-section of the airfoil and calculate its properties.

The NACA four-digit wing sections define the profile by:^{[1]}

- First digit describing maximum camber as percentage of the chord.
- Second digit describing the distance of maximum camber from the airfoil leading edge in tenths of the chord.
- Last two digits describing maximum thickness of the airfoil as percent of the chord.
^{[2]}

For example, the NACA 2412 airfoil has a maximum camber of 2% located 40% (0.4 chords) from the leading edge with a maximum thickness of 12% of the chord.

The NACA 0015 airfoil is symmetrical, the 00 indicating that it has no camber. The 15 indicates that the airfoil has a 15% thickness to chord length ratio: it is 15% as thick as it is long.

The formula for the shape of a NACA 00xx foil, with "x" being replaced by the percentage of thickness to chord, is^{[3]}

^{[4]}^{[5]}

where:

*x*is the position along the chord from 0 to 1.00 (0 to 100%),- is the half thickness at a given value of
*x*(centerline to surface), *t*is the maximum thickness as a fraction of the chord (so*t*gives the last two digits in the NACA 4-digit denomination divided by 100).

Note that in this equation, at *x*/*c* = 1 (the trailing edge of the airfoil), the thickness is not quite zero. If a zero-thickness trailing edge is required, for example for computational work, one of the coefficients should be modified such that they sum to zero. Modifying the last coefficient (i.e. to -0.1036) will result in the smallest change to the overall shape of the airfoil. The leading edge approximates a cylinder with a radius of

^{[6]}

Now the coordinates of the upper airfoil surface and of the lower airfoil surface are

Symmetrical 4-digit series airfoils by default have maximum thickness at 30% of the chord from the leading edge.

The simplest asymmetric foils are the NACA 4-digit series foils, which use the same formula as that used to generate the 00xx symmetric foils, but with the line of mean camber bent. The formula used to calculate the mean camber line is^{[3]}

where

*m*is the maximum camber (100*m*is the first of the four digits),*p*is the location of maximum camber (10*p*is the second digit in the NACA xxxx description).

For this cambered airfoil, because the thickness needs to be applied perpendicular to the camber line, the coordinates and , of respectively the upper and lower airfoil surface, become^{[7]}

where

The NACA five-digit series describes more complex airfoil shapes.^{[8]} Its format is LPSTT, where:

- L: a single digit representing the theoretical optimal lift coefficient at ideal angle of attack C
_{LI}= 0.15 L (this is*not*the same as the lift coefficient*C*),_{L} - P: a single digit for the
*x*coordinate of the point of maximum camber (max. camber at*x*= 0.05 P), - S: a single digit indicating whether the camber is simple (S = 0) or reflex (S = 1),
- TT: the maximum thickness in percent of chord, as in a four-digit NACA airfoil code.

For example, the NACA 23112 profile describes an airfoil with design lift coefficient of 0.3 (0.15 × 2), the point of maximum camber located at 15% chord (5 × 3), reflex camber (1), and maximum thickness of 12% of chord length (12).

The camber line is defined in two sections:^{[9]}

where the chordwise location and the ordinate have been normalized by the chord. The constant is chosen so that the maximum camber occurs at ; for example, for the 230 camber line, and . Finally, constant is determined to give the desired lift coefficient. For a 230 camber-line profile (the first 3 numbers in the 5-digit series), is used.

3-digit camber lines provide a very far forward location for the maximum camber.

The camber line is defined as^{[9]}

The following table presents the various camber-line profile coefficients:

Camber-line profile | |||
---|---|---|---|

210 | 0.05 | 0.0580 | 361.40 |

220 | 0.10 | 0.126 | 51.640 |

230 | 0.15 | 0.2025 | 15.957 |

240 | 0.20 | 0.290 | 6.643 |

250 | 0.25 | 0.391 | 3.230 |

Camber lines such as 231 makes the negative trailing edge camber of the 230 series profile to be positively cambered. This results in a theoretical pitching moment of 0.

From

From

The following table presents the various camber-line profile coefficients:

Camber-line profile | ||||
---|---|---|---|---|

221 | 0.10 | 0.130 | 51.990 | 0.000764 |

231 | 0.15 | 0.217 | 15.793 | 0.00677 |

241 | 0.20 | 0.318 | 6.520 | 0.0303 |

251 | 0.25 | 0.441 | 3.191 | 0.1355 |

Four- and five-digit series airfoils can be modified with a two-digit code preceded by a hyphen in the following sequence:

- One digit describing the roundness of the leading edge, with 0 being sharp, 6 being the same as the original airfoil, and larger values indicating a more rounded leading edge.
- One digit describing the distance of maximum thickness from the leading edge in tenths of the chord.

For example, the NACA 1234-05 is a NACA 1234 airfoil with a sharp leading edge and maximum thickness 50% of the chord (0.5 chords) from the leading edge.

In addition, for a more precise description of the airfoil all numbers can be presented as decimals.

A new approach to airfoil design pioneered in the 1930s, in which the airfoil shape was mathematically derived from the desired lift characteristics. Prior to this, airfoil shapes were first created and then had their characteristics measured in a wind tunnel. The 1-series airfoils are described by five digits in the following sequence:

- The number "1" indicating the series.
- One digit describing the distance of the minimum-pressure area in tenths of chord.
- A hyphen.
- One digit describing the lift coefficient in tenths.
- Two digits describing the maximum thickness in percent of chord.

For example, the NACA 16-123 airfoil has minimum pressure 60% of the chord back with a lift coefficient of 0.1 and maximum thickness of 23% of the chord.

An improvement over 1-series airfoils with emphasis on maximizing laminar flow. The airfoil is described using six digits in the following sequence:

- The number "6" indicating the series.
- One digit describing the distance of the minimum pressure area in tenths of the chord.
- The subscript digit gives the range of lift coefficient in tenths above and below the design lift coefficient in which favorable pressure gradients exist on both surfaces.
- A hyphen.
- One digit describing the design lift coefficient in tenths.
- Two digits describing the maximum thickness as percent of chord.

For example, the NACA 61_{2}-315 a=0.5 has the area of minimum pressure 10% of the chord back, maintains low drag 0.2 above and below the lift coefficient of 0.3, has a maximum thickness of 15% of the chord, and maintains laminar flow over 50% of the chord.

Further advancement in maximizing laminar flow achieved by separately identifying the low-pressure zones on upper and lower surfaces of the airfoil. The airfoil is described by seven digits in the following sequence:

- The number "7" indicating the series.
- One digit describing the distance of the minimum pressure area on the upper surface in tenths of the chord.
- One digit describing the distance of the minimum pressure area on the lower surface in tenths of the chord.
- One letter referring to a standard profile from the earlier NACA series.
- One digit describing the lift coefficient in tenths.
- Two digits describing the maximum thickness as percent of chord.
- "a=" followed by a decimal number describing the fraction of chord over which laminar flow is maintained. a=1 is the default if no value is given.

For example, the NACA 712A315 has the area of minimum pressure 10% of the chord back on the upper surface and 20% of the chord back on the lower surface, uses the standard "A" profile, has a lift coefficient of 0.3, and has a maximum thickness of 15% of the chord.

Supercritical airfoils designed to independently maximize airflow above and below the wing. The numbering is identical to the 7-series airfoils except that the sequence begins with an "8" to identify the series.

**^**E. N. Jacobs, K. E. Ward, & R. M. Pinkerton. NACA Report No. 460, "The characteristics of 78 related airfoil sections from tests in the variable-density wind tunnel". NACA, 1933.**^**"Fundamentals of aerodynamics", John D. Anderson, Jr., third ed., ch. 4.- ^
^{a}^{b}Moran, Jack (2003).*An introduction to theoretical and computational aerodynamics*. Dover. p. 7. ISBN 0-486-42879-6. **^**Aerospaceweb.org | Ask Us - NACA Airfoil Series**^**Payne, Greg (8 Jul 1994),*NACA 6, 7, and 8 series*, archived from the original on April 27, 2009**^**Gordon J. Leishman.*Principles of Helicopter Aerodynamics*. p. 361.**^**Marzocca, Pier. "The NACA airfoil series" (PDF). Clarkson University. Retrieved 2016.**^**E. N. Jacobs & R. M. Pinkerton 1936 Test in the variable-density wind tunnel of related airfoils having the maximum camber unusually far forward, NACA Report No. 537.- ^
^{a}^{b}Abbott, Ira (1959).*Theory of Wing Sections: Including a Summary of Airfoil Data*. New York: Dover Publications. p. 115. ISBN 978-0486605869.

2D Flow Aerofoil Sections Source for NACA Java Java Applet Source Code for NACA 4 & 5-digit aerofoil generator

- David Lednicer's NACA airfoil coordinate generation program Before running this Windows 95 executable, read this.
- John Dreese's NACA airfoil coordinate generation program Works on Windows XP, 7 and 8.
- NACA 4 & 5-digit Excel spreadsheets
- NACA Airfoil Series

This article uses material from the Wikipedia page available here. It is released under the Creative Commons Attribution-Share-Alike License 3.0.

Popular Products

Music Scenes

Popular Artists