At one time, in wireless the term "MIMO" referred to the use of multiple antennas at the transmitter and the receiver. In modern usage, "MIMO" specifically refers to a practical technique for sending and receiving more than one data signal simultaneously over the same radio channel by exploiting multipath propagation. MIMO is fundamentally different from smart antenna techniques developed to enhance the performance of a single data signal, such as beamforming and diversity.
MIMO is often traced back to 1970s research papers concerning multi-channel digital transmission systems and interference (crosstalk) between wire pairs in a cable bundle: AR Kaye and DA George (1970), Branderburg and Wyner (1974), and W. van Etten (1975, 1976). Although these are not examples of exploiting multipath propagation to send multiple information streams, some of the mathematical techniques for dealing with mutual interference proved useful to MIMO development. In the mid-1980s Jack Salz at Bell Laboratories took this research a step further, investigating multi-user systems operating over "mutually cross-coupled linear networks with additive noise sources" such as time-division multiplexing and dually-polarized radio systems.
Methods were developed to improve the performance of cellular radio networks and enable more aggressive frequency reuse in the early 1990s. Space-division multiple access (SDMA) uses directional or smart antennas to communicate on the same frequency with users in different locations within range of the same base station. An SDMA system was proposed by Richard Roy and Björn Ottersten, researchers at ArrayComm, in 1991. Their US patent (No. 5515378 issued in 1996) describes a method for increasing capacity using "an array of receiving antennas at the base station" with a "plurality of remote users."
Arogyaswami Paulraj and Thomas Kailath proposed an SDMA-based inverse multiplexing technique in 1993. Their US patent (No. 5,345,599 issued in 1994) described a method of broadcasting at high data rates by splitting a high-rate signal "into several low-rate signals" to be transmitted from "spatially separated transmitters" and recovered by the receive antenna array based on differences in "directions-of-arrival." Paulraj was awarded the prestigious Marconi Prize in 2014 for "his pioneering contributions to developing the theory and applications of MIMO antennas. ... His idea for using multiple antennas at both the transmitting and receiving stations - which is at the heart of the current high speed WiFi and 4G mobile systems - has revolutionized high speed wireless."
In an April 1996 paper and subsequent patent, Greg Raleigh proposed that natural multipath propagation can be exploited to transmit multiple, independent information streams using co-located antennas and multi-dimensional signal processing. The paper also identified practical solutions for modulation (MIMO-OFDM), coding, synchronization, and channel estimation. Later that year (September 1996) Gerard J. Foschini submitted a paper that also suggested it is possible to multiply the capacity of a wireless link using what the author described as "layered space-time architecture."
Greg Raleigh, V. K. Jones, and Michael Pollack founded Clarity Wireless in 1996, and built and field-tested a prototype MIMO system. Cisco Systems acquired Clarity Wireless in 1998. Bell Labs built a laboratory prototype demonstrating its V-BLAST (Vertical-Bell Laboratories Layered Space-Time) technology in 1998. Arogyaswami Paulraj founded Iospan Wireless in late 1998 to develop MIMO-OFDM products. Iospan was acquired by Intel in 2003. V-BLAST was never commercialized, and neither Clarity Wireless nor Iospan Wireless shipped MIMO-OFDM products before being acquired.
Standards and commercialization
MIMO technology has been standardized for wireless LANs, 3G mobile phone networks, and 4G mobile phone networks and is now in widespread commercial use. Greg Raleigh and V. K. Jones founded Airgo Networks in 2001 to develop MIMO-OFDM chipsets for wireless LANs. The Institute of Electrical and Electronics Engineers (IEEE) created a task group in late 2003 to develop a wireless LAN standard delivering at least 100 Mbit/s of user data throughput. There were two major competing proposals: TGn Sync was backed by companies including Intel and Philips, and WWiSE was supported by companies including Airgo Networks, Broadcom, and Texas Instruments. Both groups agreed that the 802.11n standard would be based on MIMO-OFDM with 20 MHz and 40 MHz channel options. TGn Sync, WWiSE, and a third proposal (MITMOT, backed by Motorola and Mitsubishi) were merged to create what was called the Joint Proposal. In 2004, Airgo became the first company to ship MIMO-OFDM products. Qualcomm acquired Airgo Networks in late 2006. The final 802.11n standard supported speeds up to 600 Mbit/s (using four simultaneous data streams) and was published in late 2009.
Surendra Babu Mandava and Arogyaswami Paulraj founded Beceem Communications in 2004 to produce MIMO-OFDM chipsets for WiMAX. The company was acquired by Broadcom in 2010. WiMAX was developed as an alternative to cellular standards, is based on the 802.16e standard, and uses MIMO-OFDM to deliver speeds up to 138 Mbit/s. The more advanced 802.16m standard enables download speeds up to 1 Gbit/s. A nationwide WiMAX network was built in the United States by Clearwire, a subsidiary of Sprint-Nextel, covering 130 million points of presence (PoP) by mid-2012. Sprint subsequently announced plans to deploy LTE (the cellular 4G standard) covering 31 cities by mid-2013 and to shut down its WiMAX network by the end of 2015.
The first 4G cellular standard was proposed by NTT DoCoMo in 2004. Long term evolution (LTE) is based on MIMO-OFDM and continues to be developed by the 3rd Generation Partnership Project (3GPP). LTE specifies downlink rates up to 300 Mbit/s, uplink rates up to 75 Mbit/s, and quality of service parameters such as low latency.LTE Advanced adds support for picocells, femtocells, and multi-carrier channels up to 100 MHz wide. LTE has been embraced by both GSM/UMTS and CDMA operators.
The first LTE services were launched in Oslo and Stockholm by TeliaSonera in 2009. There are currently more than 360 LTE networks in 123 countries operational with approximately 373 million connections (devices).
Precoding is multi-stream beamforming, in the narrowest definition. In more general terms, it is considered to be all spatial processing that occurs at the transmitter. In (single-stream) beamforming, the same signal is emitted from each of the transmit antennas with appropriate phase and gain weighting such that the signal power is maximized at the receiver input. The benefits of beamforming are to increase the received signal gain - by making signals emitted from different antennas add up constructively - and to reduce the multipath fading effect. In line-of-sight propagation, beamforming results in a well-defined directional pattern. However, conventional beams are not a good analogy in cellular networks, which are mainly characterized by multipath propagation. When the receiver has multiple antennas, the transmit beamforming cannot simultaneously maximize the signal level at all of the receive antennas, and precoding with multiple streams is often beneficial. Note that precoding requires knowledge of channel state information (CSI) at the transmitter and the receiver.
Spatial multiplexing requires MIMO antenna configuration. In spatial multiplexing, a high-rate signal is split into multiple lower-rate streams and each stream is transmitted from a different transmit antenna in the same frequency channel. If these signals arrive at the receiver antenna array with sufficiently different spatial signatures and the receiver has accurate CSI, it can separate these streams into (almost) parallel channels. Spatial multiplexing is a very powerful technique for increasing channel capacity at higher signal-to-noise ratios (SNR). The maximum number of spatial streams is limited by the lesser of the number of antennas at the transmitter or receiver. Spatial multiplexing can be used without CSI at the transmitter, but can be combined with precoding if CSI is available. Spatial multiplexing can also be used for simultaneous transmission to multiple receivers, known as space-division multiple access or multi-user MIMO, in which case CSI is required at the transmitter. The scheduling of receivers with different spatial signatures allows good separability.
Diversity coding techniques are used when there is no channel knowledge at the transmitter. In diversity methods, a single stream (unlike multiple streams in spatial multiplexing) is transmitted, but the signal is coded using techniques called space-time coding. The signal is emitted from each of the transmit antennas with full or near orthogonal coding. Diversity coding exploits the independent fading in the multiple antenna links to enhance signal diversity. Because there is no channel knowledge, there is no beamforming or array gain from diversity coding.
Diversity coding can be combined with spatial multiplexing when some channel knowledge is available at the receiver.
Per Antenna Rate Control (PARC), Varanasi, Guess (1998), Chung, Huang, Lozano (2001)
Selective Per Antenna Rate Control (SPARC), Ericsson (2004)
The physical antenna spacing is selected to be large; multiple wavelengths at the base station. The antenna separation at the receiver is heavily space-constrained in handsets, though advanced antenna design and algorithm techniques are under discussion. Refer to: multi-user MIMO
Recently, results of research on multi-user MIMO technology have been emerging. While full multi-user MIMO (or network MIMO) can have a higher potential, practically, the research on (partial) multi-user MIMO (or multi-user and multi-antenna MIMO) technology is more active.
In recent 3GPP and WiMAX standards, MU-MIMO is being treated as one of the candidate technologies adoptable in the specification by a number of companies, including Samsung, Intel, Qualcomm, Ericsson, TI, Huawei, Philips, Nokia, and Freescale. For these and other firms active in the mobile hardware market, MU-MIMO is more feasible for low-complexity cell phones with a small number of reception antennas, whereas single-user SU-MIMO's higher per-user throughput is better suited to more complex user devices with more antennas.
SDMA represents either space-division multiple access or super-division multiple access where super emphasises that orthogonal division such as frequency and time division is not used but non-orthogonal approaches such as superposition coding are used.
A form of space diversity scheme which uses multiple transmit or receive base stations for communicating coherently with single or multiple users which are possibly distributed in the coverage area, in the same time and frequency resource.
The transmitters are far apart in contrast to traditional microdiversity MIMO schemes such as single-user MIMO. In a multi-user macrodiversity MIMO scenario, users may also be far apart. Therefore, every constituent link in the virtual MIMO link has distinct average link SNR. This difference is mainly due to the different long-term channel impairments such as path loss and shadow fading which are experienced by different links.
Macrodiversity MIMO schemes pose unprecedented theoretical and practical challenges. Among many theoretical challenges, perhaps the most fundamental challenge is to understand how the different average link SNRs affect the overall system capacity and individual user performance in fading environments.
Routing a cluster by a cluster in each hop, where the number of nodes in each cluster is larger or equal to one. MIMO routing is different from conventional (SISO) routing since conventional routing protocols route node-by-node in each hop.
a technology where the number of terminals is much less than the number of base station (mobile station) antennas. In a rich scattering environment, the full advantages of the massive MIMO system can be exploited using simple beamforming strategies such as maximum ratio transmission (MRT), maximum ratio-combining (MRC) or zero forcing (ZF). To achieve these benefits of massive MIMO, accurate CSI must be available perfectly. However, in practice, the channel between the transmitter and receiver is estimated from orthogonal pilot sequences which are limited by the coherence time of the channel. Most importantly, in a multicell setup, the reuse of pilot sequences of several co-channel cells will create pilot contamination. When there is pilot contamination, the performance of massive MIMO degrades quite drastically. To alleviate the effect of pilot contamination, the work of proposes a simple pilot assignment and channel estimation method from limited training sequences. However, in 2018 research by Emil Björnson, Jakob Hoydis, Luca Sanguinetti was published which has shown that pilot contamination is soluble and have found that capacity of a channel can always be increased, both in theory and practice by increasing the number of antennas.
MIMO technology can be used in non-wireless communications systems. One example is the home networking standard ITU-TG.9963, which defines a powerline communications system that uses MIMO techniques to transmit multiple signals over multiple AC wires (phase, neutral and ground).
MIMO channel model
In MIMO systems, a transmitter sends multiple streams by multiple transmit antennas. The transmit streams go through a matrix channel which consists of all paths between the transmit antennas at the transmitter and receive antennas at the receiver. Then, the receiver gets the received signal vectors by the multiple receive antennas and decodes the received signal vectors into the original information. A narrowbandflat fading MIMO system is modelled as:
where and are the receive and transmit vectors, respectively, and and are the channel matrix and the noise vector, respectively.
Ergodic closed-loop (channel is known, perfect CSI) and ergodic open-loop (channel is unknown, no CSI) capacities. Number of transmit and receive antennas is 4 ().
where denotes Hermitian transpose and is the ratio between transmit power and noise power (i.e., transmit SNR). The optimal signal covariance is achieved through singular value decomposition of the channel matrix and an optimal diagonal power allocation matrix . The optimal power allocation is achieved through waterfilling, that is
where are the diagonal elements of , is zero if its argument is negative, and is selected such that .
If the transmitter has no channel state information it can select the signal covariance to maximize channel capacity under worst-case statistics, which means and accordingly
Depending on the statistical properties of the channel, the ergodic capacity is no greater than times larger than that of a SISO system.
MIMO signal testing focuses first on the transmitter/receiver system. The random phases of the sub-carrier signals can produce instantaneous power levels that cause the amplifier to compress, momentarily causing distortion and ultimately symbol errors. Signals with a high PAR (peak-to-average ratio) can cause amplifiers to compress unpredictably during transmission. OFDM signals are very dynamic and compression problems can be hard to detect because of their noise-like nature.
Knowing the quality of the signal channel is also critical. A channel emulator can simulate how a device performs at the cell edge, can add noise or can simulate what the channel looks like at speed. To fully qualify the performance of a receiver, a calibrated transmitter, such as a vector signal generator (VSG), and channel emulator can be used to test the receiver under a variety of different conditions. Conversely, the transmitter's performance under a number of different conditions can be verified using a channel emulator and a calibrated receiver, such as a vector signal analyzer (VSA).
Understanding the channel allows for manipulation of the phase and amplitude of each transmitter in order to form a beam. To correctly form a beam, the transmitter needs to understand the characteristics of the channel. This process is called channel sounding or channel estimation. A known signal is sent to the mobile device that enables it to build a picture of the channel environment. The mobile device sends back the channel characteristics to the transmitter. The transmitter can then apply the correct phase and amplitude adjustments to form a beam directed at the mobile device. This is called a closed-loop MIMO system. For beamforming, it is required to adjust the phases and amplitude of each transmitter. In a beamformer optimized for spatial diversity or spatial multiplexing, each antenna element simultaneously transmits a weighted combination of two data symbols.
Papers by Gerard J. Foschini and Michael J. Gans, Foschini and Emre Telatar have shown that the channel capacity (a theoretical upper bound on system throughput) for a MIMO system is increased as the number of antennas is increased, proportional to the smaller of the number of transmit antennas and the number of receive antennas. This is known as the multiplexing gain and this basic finding in information theory is what led to a spurt of research in this area. Despite the simple propagation models used in the aforementioned seminal works, the multiplexing gain is a fundamental property that can be proved under almost any physical channel propagation model and with practical hardware that is prone to transceiver impairments.
Papers by Dr. Fernando Rosas and Dr. Christian Oberli have shown that the entire MIMO SVD link can be approximated by the average of the SER of Nakagami-m channels. This leads to characterise the eigenchannels of N × N MIMO channels with N larger than 14, showing that the smallest eigenchannel distributes as a Rayleigh channel, the next four eigenchannels closely distributes as Nakagami-m channels with m = 4, 9, 25 and 36, and the N - 5 remaining eigenchannels have statistics similar to an additive white Gaussian noise (AWGN) channel within 1 dB signal-to-noise ratio. It is also shown that 75% of the total mean power gain of the MIMO SVD channel goes to the top third of all the eigenchannels.
A textbook by A. Paulraj, R. Nabar and D. Gore has published an introduction to this area. There are many other principal textbooks available as well.
There exists a fundamental tradeoff between transmit diversity and spatial multiplexing gains in a MIMO system (Zheng and Tse, 2003). In particular, achieving high spatial multiplexing gains is of profound importance in modern wireless systems.
Given the nature of MIMO, it is not limited to wireless communication. It can be used for wire line communication as well. For example, a new type of DSL technology (gigabit DSL) has been proposed based on binder MIMO channels.
Sampling theory in MIMO systems
An important question which attracts the attention of engineers and mathematicians is how to use the multi-output signals at the receiver to recover the multi-input signals at the transmitter. In Shang, Sun and Zhou (2007), sufficient and necessary conditions are established to guarantee the complete recovery of the multi-input signals.
^ abBerger, Lars T.; Schwager, Andreas; Pagani, Pascal; Schneider, Daniel M. (February 2014). MIMO Power Line Communications: Narrow and Broadband Standards, EMC, and Advanced Processing. Devices, Circuits, and Systems. CRC Press. doi:10.1201/b16540-1. ISBN978-1-4665-5752-9.
^Kaye, AR; George, DA (October 1970). "Transmission of multiplexed PAM signals over multiple channel and diversity systems". IEEE Transactions on Communication Technology. 18 (5): 520-526. doi:10.1109/TCOM.1970.1090417.
^B. Kumbhani, R S Kshetrimayum (2017). MIMO Wireless Communications over Generalized Fading Channels. CRC Press.
^Karakayali, M.K.; Foschini, G.J.; Valenzuela, R.A. (2006). "Advances in smart antennas - Network coordination for spectrally efficient communications in cellular systems". IEEE Wireless Communications. 13 (4): 56-61. doi:10.1109/MWC.2006.1678166.
^Gesbert, David; Hanly, Stephen; Huang, Howard; Shamai Shitz, Shlomo; Simeone, Osvaldo; Yu, Wei (2010). "Multi-Cell MIMO Cooperative Networks: A New Look at Interference". IEEE Journal on Selected Areas in Communications. 28 (9): 1380-1408. CiteSeerX10.1.1.711.7850. doi:10.1109/JSAC.2010.101202.
^Basnayaka, Dushyantha A.; Smith, Peter J.; Martin, Phillipa A. (2013). "Performance Analysis of Macrodiversity MIMO Systems with MMSE and ZF Receivers in Flat Rayleigh Fading". IEEE Transactions on Wireless Communications. 12 (5): 2240-2251. arXiv:1207.6678. doi:10.1109/TWC.2013.032113.120798.
^S. Cui; A. J. Goldsmith & A. Bahai (August 2004). "Energy-efficiency of MIMO and Cooperative MIMO in Sensor Networks". IEEE Journal on Selected Areas in Communications. 22 (6): 1089-1098. doi:10.1109/JSAC.2004.830916.
^Marzetta, Thomas L. (2010). "Noncooperative Cellular Wireless with Unlimited Numbers of Base Station Antennas". IEEE Transactions on Wireless Communications. 9 (11): 3590-3600. doi:10.1109/TWC.2010.092810.091092.
^Lo, T.K.Y. (1999). "Maximum ratio transmission". IEEE Transactions on Communications. 47 (10): 1458-1461. doi:10.1109/26.795811.
^W. C. Jakes, Jr., Mobile Microwave Communication. New York: Wiley, 1974.
^Gerard J. Foschini & Michael. J. Gans (January 1998). "On limits of wireless communications in a fading environment when using multiple antennas". Wireless Personal Communications. 6 (3): 311-335. doi:10.1023/A:1008889222784.
^Gerard J. Foschini (Autumn 1996). "Layered space-time architecture for wireless communications in a fading environment when using multi-element antennas". Bell Labs Technical Journal. 1 (2): 41-59. doi:10.1002/bltj.2015.
^Rosas, F. & Oberli, C. (April 16, 2013). "Nakagami-m approximations for multiple-input multiple-output singular value decomposition transmissions". IET Communications. 7 (6): 554-561. doi:10.1049/iet-com.2012.0400.
^A. Paulraj, R. Nabar & D. Gore (2003). Introduction to Space-time Communications. Cambridge University Press.
^David Tse; Pramod Viswanath (2005). Fundamentals of Wireless Communication. Cambridge.
^Claude Oestges; Bruno Clerckx (2007). MIMO Wireless Communications: From Real-world Propagation to Space-time Code Design. Academic Press.
^Ezio Biglieri; Robert Calderbank; Anthony Constantinides; Andrea Goldsmith; Arogyaswami Paulraj; H. Vincent Poor (2010). MIMO Wireless Communications. Cambridge University Press.