Galena, Sulphuret of lead
3D model (JSmol)
CompTox Dashboard (EPA)
|Melting point||1,118 °C (2,044 °F; 1,391 K)|
|Boiling point||1,281 °C (2,338 °F; 1,554 K)|
|2.6×10-11kg/kg (calculated, at pH=7) 8.6×10-7 kg/kg|
Solubility product (Ksp)
Refractive index (nD)
|Halite (cubic), cF8|
|Fm3m, No. 225|
a = 5.936Å
Heat capacity (C)
Std enthalpy of
|Safety data sheet||External MSDS|
|GHS Signal word||Danger|
|H302, H332, H360, H373, H400, H410|
|P201, P202, P260, P261, P264, P270, P271, P273, P281, P301+312, P304+312, P304+340, P308+313, P312, P314, P330, P391, P405, P501|
|NFPA 704 (fire diamond)|
Except where otherwise noted, data are given for materials in their standard state (at 25 °C [77 °F], 100 kPa).
|what is ?)(|
Lead(II) sulfide (also spelled sulphide) is an inorganic compound with the formula PbS. Galena is the principal ore and the most important compound of lead. It is a semiconducting material with niche uses.
Addition of hydrogen sulfide or sulfide salts to a solution containing a lead salt, such as PbCl2, gives a black precipitate of lead sulfide.
This reaction is used in qualitative inorganic analysis. The presence of hydrogen sulfide or sulfide ions may be tested using "lead acetate paper."
Like the related materials PbSe and PbTe, PbS is a semiconductor. In fact, lead sulfide was one of the earliest materials to be used as a semiconductor. Lead sulfide crystallizes in the sodium chloride motif, unlike many other IV-VI semiconductors.
Since PbS is the main ore of lead, much effort has focused on its conversion. A major process involves smelting of PbS followed by reduction of the resulting oxide. Idealized equations for these two steps are:
Lead sulfide-containing nanoparticle and quantum dots have been well studied. Traditionally, such materials are produced by combining lead salts with a variety of sulfide sources. PbS nanoparticles have been recently examined for use in solar cells.
Although of little commercial value, PbS is one of the oldest and most common detection element materials in various infrared detectors. As an infrared detector, PbS functions as a photon detector, responding directly to the photons of radiation, as opposed to thermal detectors, which respond to a change in detector element temperature caused by the radiation. A PbS element can be used to measure radiation in either of two ways: by measuring the tiny photocurrent the photons cause when they hit the PbS material, or by measuring the change in the material's electrical resistance that the photons cause. Measuring the resistance change is the more commonly used method. At room temperature, PbS is sensitive to radiation at wavelengths between approximately 1 and 2.5 ?m. This range corresponds to the shorter wavelengths in the infra-red portion of the spectrum, the so-called short-wavelength infrared (SWIR). Only very hot objects emit radiation in these wavelengths.
Cooling the PbS elements, for example using liquid nitrogen or a Peltier element system, shifts its sensitivity range to between approximately 2 and 4 ?m. Objects that emit radiation in these wavelengths still have to be quite hot--several hundred degrees Celsius--but not as hot as those detectable by uncooled sensors. (Other compounds used for this purpose include indium antimonide (InSb) and mercury-cadmium telluride (HgCdTe), which have somewhat better properties for detecting the longer IR wavelengths.) The high dielectric constant of PbS leads to relatively slow detectors (compared to silicon, germanium, InSb, or HgCdTe).
PbS was once used as a black pigment.
Elevations above 2.6 km (1.63 mi) on the planet Venus are coated with a shiny substance. Though the composition of this coat is not entirely certain, one theory is that Venus "snows" crystallized lead sulfide much as Earth snows frozen water. If this is the case, it would be the first time the substance was identified on a foreign planet. Other less likely candidates for Venus' "snow" are bismuth sulfide and tellurium.
Lead(II) sulfide is so insoluble that it is almost nontoxic, but pyrolysis of the material, as in smelting, gives dangerous fumes. Lead sulfide is insoluble and a stable compound in the pH of blood and so is probably one of the less toxic forms of lead. A large safety risk occurs in the synthesis of PbS using lead carboxylates, as they are particularly soluble and can cause negative physiological conditions.